Categories

Manufactures
























Casale V-Drive Gear Promotion
Casale Bearings & Seals

UPS Shipping Information
Click Here for
Shipping Time Map



Like us on Facebook!







Home > D21 Enterprises
Sort By:
Page of 1
D21 Cavitation Rod Seal Kit
D21 Cavitation Rod Seal Kit
Our Price: $12.95

Rebuild kit for the D21 Enterprises Cavitation thru hull seal

Kit comes with two 1/2" double lip grease seals and one o-ring

...
D21 1" Prop Shaft Seal Rebuild Kit
D21 1" Prop Shaft Seal Rebuild Kit
Our Price: $22.95

Replacement bearing and seal kit for the D21 1" prop shaft seal
Precision bored, sealed bearing and two double lip grease cup seals.

Sold as set

...
D21 1-1/8" Prop Shaft Seal Rebuild Kit
D21 1-1/8" Prop Shaft Seal Rebuild Kit
Our Price: $22.95

Replacement bearing and seal kit for the D21 1-1/8" prop shaft seal
Precision bored, sealed bearing and two double lip grease cup seals.

Sold as set

...
Billet Aluminum J-Drain Cover Only
Billet Aluminum J-Drain Cover Only
Our Price: $36.00

Replaces the existing J-drains that tend to leak by converting it to a 1" twist style drain plug

Machined from 6061 T6 aluminum that can be easily polished, Anodized, or powdercoated to match your hardware.

Fits the standard 2" X 2" J-Drain. Bolts right into the existing holes for a clean installation

...
Billet Aluminum Cavitation Thru Hull Seal Assy.
Billet Aluminum Cavitation Thru Hull Seal Assy.
Our Price: $42.00

Replacement Cavitation thru hull seal assembly for your cavitation rod. Machined from billet 6061-T6 aluminum with machine finish

They have two double lip cup seals with a gap in between them for grease. A snap ring on the front for containment and safety. Also an O-ring on the water side for a total of 3 water seals!

Hose Size: 1-1/4"
Shaft size: 1/2"

...
1" Seal Type Stuffing Box with Bearing
1" Seal Type Stuffing Box with Bearing
Our Price: $89.00

Made from 6061-T6 aluminum with a machined finish. They are approximately 2 1/2" diameter by 2 1/2" long. There is a lightly pressed in 2" diameter double sealed bearing with the inside diameter bored to 1.002" (to easily slip over your prop shaft). It’s held in the aluminum housing by a snap ring for safety.

Inside the aluminum housing is a double lip cup seal to keep the water out and a grease zerk on the outside body to grease the seal. A standard size 1 3/4" hose fits from the rear, Also added rounded grooves to help the hose clamp bite into the housing and not slip off.
With this design there will be no more prop shaft wear of bushings to replace because it rides on a bearing!

...
1-1/8" Seal Type Stuffing Box with Bearing
1-1/8" Seal Type Stuffing Box with Bearing
Our Price: $99.00

Made from 6061-T6 aluminum with a machined finish. They are approximately 3" diameter by 2 7/8" long. There is a lightly pressed in 2 1/2" diameter double sealed bearing with the inside diameter bored to 1.128" (to easily slip over your prop shaft). It’s held in the aluminum housing by a snap ring for safety.

Inside the aluminum housing is a double lip cup seal to keep the water out and a grease zerk on the outside body to grease the seal. A standard size 1 3/4" hose fits from the rear, Also added rounded grooves to help the hose clamp bite into the housing and not slip off.

With this design there will be no more prop shaft wear of bushings to replace because it rides on a bearing!

...
Billet Aluminum Rudder Stuffing Box With Bearing 1"
1" Billet Aluminum Rudder Stuffing Box With Bearing
Discount Price $195.00

Made from 6061 T6 aluminum with a machined finish. Designed to fit 1" diameter rudder shafts.
The stuffing box has a standard 3-5/16" square mounting flange. It is a direct replacement for your older style stuffing box. Mounting holes are not drilled as every hull has a different variety of hole sizes and patterns. All you have to do is transfer the existing hole locations in you hull to the rudder box and drill the size you need.

Fits all standard 1-1/2" diameter thru hull holes. The section that goes thru the bottom of the hull is 1-3/4" long to accommodate any hull thickness. Cut the length to fit.

Overall height of the stuffing box inside the boat is 2-1/8"

From the top of the stuffing box to the bottom features a snap ring for safety to help retain the 1" sealed bearing that is bored a few thousands larger than your rudder shaft for easy installation.

Next is an ample sized grease reservoir which is filled by the grease zerk located on the outside of the rudder box housing

A double lip grease cup seal is lightly pressed in as a second barrier to keep water out. The first water barrier is a 1/8" diameter o-ring that is below the grease cup seal.

Recommended Sea Going Epoxy putty for installation

...
Billet Aluminum Rudder Stuffing Box With Bearing 1-1/8"
1-1/8" Billet Aluminum Rudder Stuffing Box With Bearing
Discount Price $195.00

Made from 6061 T6 aluminum with a machined finish. Designed to fit 1-1/8" diameter rudder shafts.
The stuffing box has a standard 3-5/16" square mounting flange. It is a direct replacement for your older style stuffing box. Mounting holes are not drilled as every hull has a different variety of hole sizes and patterns. All you have to do is transfer the existing hole locations in you hull to the rudder box and drill the size you need.

Fits all standard 1-1/2" diameter thru hull holes. The section that goes thru the bottom of the hull is 1-3/4" long to accommodate any hull thickness. Cut the length to fit.

Overall height of the stuffing box inside the boat is 2-5/16"

From the top of the stuffing box to the bottom features a snap ring for safety to help retain the 1-1/8" sealed bearing that is bored a few thousands larger than your rudder shaft for easy installation.

Next is an ample sized grease reservoir which is filled by the grease zerk located on the outside of the rudder box housing

A double lip grease cup seal is lightly pressed in as a second barrier to keep water out. The first water barrier is a 1/8" diameter o-ring that is below the grease cup seal.

Recommended Sea Going Epoxy putty for installation

...
Billet Aluminum Rudder Stuffing Box Round Base With Bearing 1"
1" Billet Aluminum Rudder Stuffing Box With Bearing Round Flange
Discount Price $195.00

Made from 6061 T6 aluminum with a machined finish. Designed to fit 1" diameter rudder shafts.
The stuffing box has a standard 4-1/16" round mounting flange. It is a direct replacement for your older style stuffing box. Mounting holes are not drilled as every hull has a different variety of hole sizes and patterns. All you have to do is transfer the existing hole locations in you hull to the rudder box and drill the size you need.

Fits all standard 1-1/2" diameter thru hull holes. The section that goes thru the bottom of the hull is 1-3/4" long to accommodate any hull thickness. Cut the length to fit.

Overall height of the stuffing box inside the boat is 2-1/8"

From the top of the stuffing box to the bottom features a snap ring for safety to help retain the 1" sealed bearing that is bored a few thousands larger than your rudder shaft for easy installation.

Next is an ample sized grease reservoir which is filled by the grease zerk located on the outside of the rudder box housing

A double lip grease cup seal is lightly pressed in as a second barrier to keep water out. The first water barrier is a 1/8" diameter o-ring that is below the grease cup seal.

Recommended Sea Going Epoxy putty for installation

...
1" Billet Aluminum Quadrant
1" Billet Aluminum Quadrant grooved finish
Our Price: $249.00

Machined from 6061-T6 aluminum. Standard 1" bore for rudders with a 1" shaft. 1/4 keyway

Top cable clamp features two milled in scallops to help "bite" into the standard 3/16" cable. Top clamp has a built in clearance when tightened onto steering cable it will be flush with the top surface. Supplied with 2 1/4" corrosion resistance grade 8 bolts that screws onto two heli-coiled holes installed into the quadrant.
...

1" Billet Aluminum Quadrant
1" Billet Aluminum Quadrant smooth finish
Our Price: $249.00

Machined from 6061-T6 aluminum. Standard 1" bore for rudders with a 1" shaft. 1/4 keyway

Top cable clamp features two milled in scallops to help "bite" into the standard 3/16" cable. Top clamp has a built in clearance when tightened onto steering cable it will be flush with the top surface.


....